How to install a satellite tv dish

Its design is also very important because it can determine the power and quality of reception. In addition to the type of antenna, another important point is the size: the lower the quality of the satellite signal in our geographical area, the greater the plate should be. These are the most common types of satellite antenna dishes :.

The LNB This device Low Noise Block , literally translated as a low noise block is used to process the signals emitted by the satellites and convert them into a lower frequency so that they can be distributed smoothly to the receiver. The image quality on the screen will depend on its quality. These devices can be:.

The support of the LNB. It is the arm at whose end the LNB is placed stably so that it can be oriented according to the reception parameters. It is attached to the wall bracket, to the mast of a collective antenna, or to the mast of the floor of a terrace, usually by means of U-bolts or very resistant jaws.

It is also used to place the plate anchors and the height adjustment systems of the plate. The height regulator It allows to orientate the height of the plate for the correct reception according to the satellite. It has some through screws with nuts that can be loosened and tightened to adjust the orientation.

The azimuth regulator. The wall or mast support usually a cylindrical tube is the axis that allows the azimuth to be adjusted with respect to the satellite, starting from the north cardinal point or the magnetic north. To do this you have to rotate the structure with the plate around it. Its manipulation allows to capture the satellite signals, combining it with the height of the parabola.

The azimuth adjustment is made clockwise or counterclockwise. The wire. When installing a satellite dish, it is essential to use the correct cable. You must use a coaxial cable of satellite quality, somewhat thicker than the one used inside, with its corresponding connectors. In the cable sheath you will find information about its uses.

The satellite receiver It is the device that transforms the signal received by the antenna so that it can be seen on televisions. It is the point at which the coaxial cable arrives from the satellite dish, and from which the cable that goes to the TV comes out. It is best to make this connection with HDMI, so that there is no loss of sharpness in the image.

In addition, with a cable or wireless connection you can receive Internet services that are contracted with the telephone company. Does your building have a home automation network and do you want to install a satellite dish? The installation wiring can be used to channel the antenna cable to your home if they give you the corresponding authorization. In a single-family home, you will only have to attend to the possible urban norms.

Once each part of the kit has been identified, it is time to mount the parabolic and then install it at the appropriate point. In general, the steps are as follows:. Step 1. Fix the anchor legs of the support to the back of the plate: normally it is placed with four through screws and four nuts.

Do it with their corresponding screws and nuts. Tighten the screw with a flat wrench. Put the LNB, but do not tighten at all until regular.

When you bolt the wall mount in place, the tails open up, making the plugs harder to remove. Secure the plugs into the wall with a hammer and chisel. Place the tip of a chisel against one of the bolts.

Give the chisel's handle a couple of good whacks to push the bolt into the wall. Keep hammering until the bolt is flush with the wall.

Then, repeat this with the remaining bolts. Make sure the bolts are level with the wall, or else the dish's mount won't anchor properly.

Place the metal plugs and hammer them into the wall. Your dish will come with a set of plugs that serve as wall anchors. Position them, so their open end faces out from the wall.

That opening is for bolting the wall mount in place. After pushing the plugs into the holes, tap them in with a hammer and chisel. They are what anchors the mount to the wall or ceiling. If they are loose, your dish could end up crashing to the ground! Bolt the mount onto the plugs in the wall. Position the mount back on the wall, lining up the plate's holes with the pilot holes you drilled. Fasten the bolts by using a cordless screwdriver.

Make sure the mount feels secure in the wall before you move on. If you're sure they are in correctly, take them out and recheck the plugs. Cap each bolt with a metal washer and locking nut. These components prevent the bolts from coming back out of the wall. Slide the washers on first, which are flat metal disks that help the nuts work properly.

Then, add the nuts and turn them clockwise with a wrench until they feel tight and no longer move. Be careful not to overtighten the nuts. Stop twisting them when they become hard to move. As long as they are not loose, the mount will also stay in place. Part 2. Attach the antenna bracket to the low noise block LNB arm. Your dish will most likely come with a flat metal plate to connect the satellite dish to the L-shaped LNB arm and other components. Position the plate, so the prongs are on the left and right, facing you.

Hold the LNB arm between the prongs with the tail end extending out past the plate's opposite side. The exact installation process, including the bolts' size, may vary a little depending on the dish you have.

Refer to the owner's manual for more specific instructions. Clip the antenna adjustment panel over the plate's prongs. The panel will look like a square box with one end open. Add a washer and nut on the end of each bolt after tightening them. This slot is what you use to point the satellite up or down. Fit the U-shaped rod inside the adjustment panel. Your dish will have a bent metal rod that fits into one of the slots on the adjustment panel.

Slip the rod inside, sliding its prongs through the holes. Ensure the prongs point toward you rather than the tail end of the LNB rod you connected earlier. Fit a small clamp over it, followed by a washer and nut on each prong. The adjustment panel has 3 different slots. Use the slots to reposition the satellite dish. In most cases, the middle slot is best for setting the dish at the proper angle.

Bolt the antenna bracket to the back of the satellite dish. You have a couple more bolts to add to finish the bulk of the assembly, and this is one of the easiest parts to finish. Line up the holes on the plate with the holes on the back of the dish. Stick the longest bolts you have, usually 2 to 3 in 5. Then, place a washer and nut on the end of each bolt, tightening it with your wrench.

If they feel shaky, carefully separate them and tighten the bolts. One last component, the LNB, controls the dish's functionality. First, slide the handle of the LNB onto the open end of the arm.

Secure it with nuts and bolts, then take the LNB out of the box. It looks almost like a round speaker or flashlight. Position it on the handle, facing it toward the dish before bolting it in place. You may need to loosen the LNB later to readjust it and improve the signal quality. Connect the adjustment panel on the dish to the wall mount. Fit the dish onto the open end of the support. If everything is attached correctly, it will fit inside or behind the adjustment panel. You can then add the 1 or 2 remaining bolts to fasten these pieces together.

If the dish looks good, then you're ready to position it to communicate with a satellite. If the mount is meant to attach to the back of the panel, your satellite will also come with a pair of clips. Position them behind the support, then add the screws through them to bind the parts together. Part 3. Select a satellite you wish to connect to. Pick a satellite that is in range of your particular dish.

There are numerous satellites out there, but dishes cannot get signals from all of them. If you bought your dish from a TV service, for instance, you might have a hard time connecting to their competitor's satellites. Tracking sites list the names, which usually include the owning company or the service they provide. If you bought a satellite service, it is possible to receive satellite signals outside that service. Since you usually need to replace several parts, it's easier to get a new satellite instead.

Try to pick a satellite close to your area. If you subscribe to a particular TV service, you will need to use the company's satellites. The biggest providers have multiple satellites. This is a cord or a wire connected to the LNB on a satellite tv dish to the receiver and it is usually in black or white color. Example of coaxial cable shown below. F-Connector have a nut head painted with silver and the function of F-Connector gripped the wire firmly and tied the nut to the LNB or receiver as shown below:.

Note: Selecting dish location is crucial to make dish installation easier you need to choose a place very close to signal location and the dish needs to be free from obstacles such as house, trees and so on. This is the best way to learn how to install satellite tv dish and receiver and if you face any difficulty during the installation of dish feel free to leave comment below or use our site contact form to reach and usually response take less than 24hours and If you like this tutorial please share it with your friends, family and also share across social media thanks and see you in the next episode.

Hi iam having difficulties in getting the mbc channels that is mbc 1,2,3 max and action which is the exact position? What i know is near dstv position.. Alternatively point your satellite dish to Eutelsat 7A At 7E. I mistakenly press a button on my digicom channels receiver and all the channels are gone, pls how will I restore them? Press menu 2. Navigate to Satellite installation 3. Press blue button to scan 5. Press OK button twice or scroll down Scan option and press ok button to start scanning 7.

After the scanning completed 8. Press exit button to clear the menu screen an start enjoying your channels.